Bureau Veritas Welcomes 3rd Amendment to 18th Edition, but says it ‘Sparks’ a Renewed Focus for Duty Holders

• Content
• Building Services
• Bureau Veritas Welcomes 3rd Amendment to 18th Edition, but says it ‘Sparks’ a Renewed Focus for Duty Holders

23 August 2024 | Updated 28 August 2024

Martin Sampson from Bureau Veritas outlines the latest regulatory changes for FMs dealing with electrical installations on their premises.

On 31 July 2024, the Institution of Engineering and Technology (IET) released its third amendment to BS7671: 2018 (18th Edition) Wiring Regulations. The Regulations apply to the design, erection and verification of electrical installations, as well as additions and alterations to existing installations, and is intended to be implemented immediately. Welcoming this amendment as a positive and essential step forward for the industry, electrical expert and Technical Manager at Bureau Veritas, Martin Sampson, stresses the need for duty holders to remain on top of the frequently changing regulations to ensure utmost safety for electrical users.

With a compliance career spanning over 20 years, Martin has worked in electrical and mechanical maintenance roles, as well as an electrical engineer surveyor, responsible for fixed electrical wiring installations, hazardous and explosive areas, and commercial premises. At Bureau Veritas, Martin leads the electrical division, responsible for training and standards of 60 engineer surveyors, ensuring technical standards are maintained across the entire discipline. 

 

"The difficulty for duty holders is its often not feasible or realistic to be across these ever-changing regulations for which they may not be a specialist. However, the onus and responsibility are firmly on them to ensure electrical installations under their responsibility, remain safe for users."

 

BS 7671:2018+A3:2024 Requirements for Electrical Installations

 

BS 7671:2018+A3:2024 Requirements for Electrical Installations aims to address the requirements for the correct connections of unidirectional and bidirectional residual current devices (RCDs) and miniature circuit breakers (MCBs). 

According to the amendment:

 

• A bidirectional protective device is a protective device where it is intended by the manufacturer that a source of supply is connected to either or both sets of connection terminals
• A unidirectional protective device is a protective device where it is intended by the manufacturer that a source of supply is only connected to one defined set of connection terminals.

 

This new focus on connection of unidirectional and bidirectional RCD & MCBs comes at a relevant time for the industry, as we’re seeing a marked rise in the demand, installation and use of renewable energy solutions. Introduction of renewable technology such as solar PV, Electric Vehicle charging or battery storage systems means that we must now consider the safety implications and likelihood of parallel supplies within a single installation.

An RCD is a safety device designed to reduce the risk of electrocution and fire, caused by earth faults; it essentially identifies a fault in an electrical system and switches it off. A unidirectional RCD will therefore only identify a fault when electricity is flowing in the one direction it was designed for. Newer technologies such solar, EV and battery storage may require bidirectional devices. The designer and installer must refer to manufacturer’s advice on where to connect these within the distribution board.

The regulations are being updated to keep pace with the advances in technology and the relevant manufacturer's guidance.

However, also important to note is the significance of yet another amendment to the wiring regulations. As the demand and scope for renewable energy sources continues to grow and develop, so too will the regulation that sits alongside it. This latest amendment to the IET 18^th Edition Wiring Regulations marks the third review of the document in six years - a notable increase in frequency compared to previous versions.

There won’t be a slow-down in regulatory change either. Despite the third amendment having only just been released, Amendment 4 is already being talked about which may bring about requirements for stationary secondary batteries, low voltage generating sets, power over ethernet (POE), and much more. All of which is in response to ever-evolving technologies being developed on the race to net-zero.

There are other fast changes too. For example, EV charging guidance is changing quickly with the Code of Practice for Electric Vehicle Charging Equipment Installation, moving onto edition 5 in 2023 after only 11 years in publication. 

The difficulty for duty holders is its often not feasible or realistic to be across these ever-changing regulations for which they may not be a specialist. However, the onus and responsibility are firmly on them to ensure electrical installations under their responsibility, remain safe for users.

As outlined in the BEAMA report which triggered this latest review of the 18^th Edition regulations, electrical installation inspectors must remain up to date with the latest testing, inspection and certification advice, so they can support duty holders on the risks of this issue for existing electrical installations, and the correct route forwards. Trusted, independent inspection partners like Bureau Veritas can work with duty holders every step of the way to navigate evolving regulations, such as these.

Picture: a photograph of an electrician repairing a fuse box. Image Credit: Pexels

Article written by Martin Sampson | Published 23 August 2024

Share

---

---

Related Articles

---